Page 1 of 2 12 LastLast
Results 1 to 10 of 15

Thread: Throttle position 256%

  1. #1
    Senior Member
    Join Date
    May 2006
    Posts
    165

    Default Throttle position 256%

    can some one tell me whats going on here my scanner is all over the place throttle position 256%, and many other pids/scanned data is all out of wack. i thought it was my laptop so wiped out the hard drive and reistalled everything and it is still f-ed up. is my pcm shot. i have a log file here http://forum.efilive.com/showthread.php?t=6156 i just checked it and it all messed up on my laptop i dont recall it being like that when i posted it. can some look at it and see if it ok Help. could this be from the drivers i installed. i recently installed the latest update. never mind turns out it was something in my custom pid file. i deleted the whole file and the problem is gone
    Last edited by vatman02; September 27th, 2007 at 01:43 PM.
    2002 ws6 stock short block
    GMPP cnc LS6 Heads 11.4:1 cr
    .576 i .581 e 116 lobe
    D1SC @ 10#
    723 rwhp 654 rwtq on E-85

  2. #2
    Lifetime Member 5.7ute's Avatar
    Join Date
    Oct 2006
    Posts
    1,840

    Default

    That log still downloads & plays fine. Have you tried reinstalling the software?

  3. #3
    Senior Member
    Join Date
    May 2006
    Posts
    165

    Default

    i just reinstalled it apparently it was the custom pids file. something was funky in there i deleted the whole file and everything seems to be fine now. i am now trying to determine what went wrong. thanks for the reply.
    2002 ws6 stock short block
    GMPP cnc LS6 Heads 11.4:1 cr
    .576 i .581 e 116 lobe
    D1SC @ 10#
    723 rwhp 654 rwtq on E-85

  4. #4
    Senior Member
    Join Date
    May 2006
    Posts
    165

    Default

    error message: "units Lambda not found". when i mess with this one *CLC-00-005
    V 0.00 5.00 .1 "{EXT.AD1}"
    LAMBDA 1.25 0.75 .1 "{CALC.LM1_EQ(EXT.AD1+7.5)}/10"

    *CLC-00-006
    factor 0.00 2.0 .3 "{CALC.LM1_EQ}/{CALC.EQ}"
    it seems to cause what ever it was. all the rest i put back in and they work fine. i just cant seem to get the EQ lambda to work. i had it in once and though it worked but i bet thats when it all went haywire. also when i tried to set the LM1 to v. 0 - 1.25 V.5 - .75 the lm1 would not allow it. it said the value must be over 1.25 for the 5 v. area
    2002 ws6 stock short block
    GMPP cnc LS6 Heads 11.4:1 cr
    .576 i .581 e 116 lobe
    D1SC @ 10#
    723 rwhp 654 rwtq on E-85

  5. #5
    Lifetime Member 5.7ute's Avatar
    Join Date
    Oct 2006
    Posts
    1,840

    Default

    I have a battery for my LM-1 now so I will have a look. That calc pids file worked fine on my computer. Did you just replace your old file with that one I sent or copy & pasted the info over?

  6. #6
    Senior Member
    Join Date
    May 2006
    Posts
    165

    Default

    i just checked it out and it seems to be doing what it is supposed to voltages match but the Ben is not working. also i had to change to this LAMBDA none LAMBDA "AFR in EQ"
    from this
    EQ none EQ " AFR in LAMBDA"
    2002 ws6 stock short block
    GMPP cnc LS6 Heads 11.4:1 cr
    .576 i .581 e 116 lobe
    D1SC @ 10#
    723 rwhp 654 rwtq on E-85

  7. #7
    Senior Member
    Join Date
    May 2006
    Posts
    165

    Default

    yes i copied and pasted but the ben does'nt work and i had to change a few things EQ to LAMBDA and V. 0.00 5.00
    LAMBDA .75 1.25
    2002 ws6 stock short block
    GMPP cnc LS6 Heads 11.4:1 cr
    .576 i .581 e 116 lobe
    D1SC @ 10#
    723 rwhp 654 rwtq on E-85

  8. #8
    Lifetime Member 5.7ute's Avatar
    Join Date
    Oct 2006
    Posts
    1,840

    Default

    While the output from the lm-1 is derived from lambda you do not want to confuse the two. They are different units.
    I will send the pid through as soon as I have it sorted.

  9. #9
    Lifetime Member 5.7ute's Avatar
    Join Date
    Oct 2006
    Posts
    1,840

    Default

    Quote Originally Posted by vatman02
    yes i copied and pasted but the ben does'nt work and i had to change a few things EQ to LAMBDA and V. 0.00 5.00
    LAMBDA .75 1.25
    I used your old calc.pid.txt file to make that pid. You should rename your original calc pid file to something like calc.pid1 & save the file I sent you as the calc.pid file. Then open the tuning tool & see how it goes.

  10. #10
    Senior Member
    Join Date
    May 2006
    Posts
    165

    Default

    i just did as stated moved my current calcc pid file to calc pid 1 and used the file sent as cal pid. if i use the one you sent it says Lambda not found then closes. that is why i change the EQ to LAMBDA and Lambda to EQ that allows it work. all but the BEN {CACL.LM1_EQ}/{CALC.EQ} not valid because unknown parameter {CALC.EQ} at position 24
    Last edited by vatman02; September 27th, 2007 at 02:57 PM.
    2002 ws6 stock short block
    GMPP cnc LS6 Heads 11.4:1 cr
    .576 i .581 e 116 lobe
    D1SC @ 10#
    723 rwhp 654 rwtq on E-85

Page 1 of 2 12 LastLast

Similar Threads

  1. Throttle position confuddlement
    By turboberserker in forum General (Petrol, Gas, Ethanol)
    Replies: 10
    Last Post: June 2nd, 2010, 06:18 AM
  2. 2010 throttle position values ??
    By 2010 Bumblebee in forum E37, E38 & E67 PFI ECM's
    Replies: 4
    Last Post: May 7th, 2010, 02:19 AM
  3. Pedal position vs. commanded TAC position weirdness
    By gmtech16450yz in forum E37, E38 & E67 PFI ECM's
    Replies: 14
    Last Post: November 1st, 2009, 11:48 AM
  4. Absolute Throttle Position
    By mvnvltn in forum General (Petrol, Gas, Ethanol)
    Replies: 3
    Last Post: December 29th, 2008, 09:22 PM
  5. Replies: 11
    Last Post: May 8th, 2005, 11:52 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •