vz v6 4l60

[zrx1200]

vz 4l60e/allytec .i see trans is supported. can you use v1 or do you have to have v2.was hoping to tweak a mates g box but have v1 only

[GMPX]

Sorry, the T42 is a CAN based controller, the V1 can't communicate on the CAN bus.

Cheers,
Ross

[OLS108]

so the V2 will allow you to edit the auto settings in the V6 ?

[swingtan]

I tried reading the TCM in the wifes VZ SV6 and can't see it at all with the V2. I think there is more to it than just the CAN bus.

[OLS108]

I tried reading the TCM in the wifes VZ SV6 and can't see it at all with the V2. I think there is more to it than just the CAN bus.

Thanks Simon.

[Biggsy]

I can edit the TCM in my VZ V6 work ute without issue with my V2

[swingtan]

Interesting.......

Any chance you have not tried the BBL Beta firmware? I've updated mine so there is a chance that's why I can't see the TCM. I'll try it tomorrow after the latest update.

Simon

[swingtan]

I just tried reading the TCM on the SV6 and got the following in the console....

08:15:41.584: Scanning for EFILive FlashScan V2 HAPI
08:15:41.784: Interface firmware version: 2.5.15
08:15:41.844: Interface firmware model: FSV2
08:15:41.864: Interface firmware version: 2.5.15
08:15:41.904: Interface firmware date: Mar 18, 2008
08:15:41.934: FlashScan serial number: 00365XXXXXX
08:15:41.964: FlashScan license number: 00365XXXXXX
08:15:42.004: Disconnecting ...
08:15:42.055: CAN-VPW Bridge Deactived
08:15:42.065: Disconnected
08:15:42.705: Scanning for EFILive FlashScan V2 HAPI
08:15:42.906: Interface firmware version: 2.5.15
08:15:42.936: CAN-VPW Bridge Actived
08:15:42.966: Current protocol set to: "ISO 15765 CAN"
08:15:45.109: Current protocol: "ISO 15765 CAN"
08:15:45.169: Interface firmware model: FSV2
08:15:45.199: Interface firmware version: 2.5.15
08:15:45.219: Interface firmware date: Mar 18, 2008
08:15:45.259: FlashScan serial number: 00365XXXXXX
08:15:45.289: FlashScan license number: 00365XXXXXX
08:15:45.399: Getting status...
08:15:45.469: Status: OK.
08:15:46.361: Bootloader version: TCM42v1.1R (035A-28A7)
08:15:46.371: Preparing TCM for reading flash...
08:15:46.411: TCM seed is: $9D0B
08:15:46.421: Unlock attempt 1 of 3
08:15:46.811: Unlock attempt 2 of 3
08:15:47.192: TCM may not be secured - did not reply to seed request
08:15:47.202: Initializing TCM...
08:15:48.464: Initializing TCM, step 1 of 4
08:15:48.464: Initializing TCM, step 2 of 4
08:15:49.726: Initializing TCM, step 3 of 4
08:15:52.229: Initializing TCM, step 4 of 4
08:15:52.510: Disconnecting ...
08:15:52.560: CAN-VPW Bridge Deactived
08:15:52.570: Disconnected

I then get the attached error message. Any one got an idea on this?

[Biggsy]

Interesting.......

Any chance you have not tried the BBL Beta firmware? I've updated mine so there is a chance that's why I can't see the TCM. I'll try it tomorrow after the latest update.

Simon

I have not installed BBL Beta, could be the problem.