Replace calc_pids.txt with the following [see attached file]
(be sure to first save your existing calc_pids.txt):
Code:
# ==============================================================================
# File details
# ------------
#
# This section defines various details about the file format.
*FILE
#Parameter Value Description
#---------- ---------------- ---------------------------------------------------
VERSION 7.1.1 File version
DECSEP . Decimal separator used in this file
# ==============================================================================
# Units
# -------------------
# See sae_generic.txt for more information on the *UNITS section
*UNITS
#Code System Abbr Description
#-------- ---------- -------- -------------------------------------------------------------
None None "" "No units"
inch Imperial "in" "Inches"
# ==============================================================================
# Add slot definitions here
# --------------------------------
# See sae_generic.txt for more information on "SLOT" formats
#
#Units Low High Fmt Expression
#------------ ------------- ------------- ---- --------------------------------------------------------------
*CLC-00-080
inch 0.0 60.0 0.2 "26.2"
*CLC-00-090
factor 0.0 10.0 0.2 "4.10"
*CLC-00-101
rpm 0 8000 0.0 "{SAE.VSS.mph} * 336 * {CALC.AXLE} * 2.66 / {CALC.TIRE}"
*CLC-00-102
rpm 0 8000 0.0 "{SAE.VSS.mph} * 336 * {CALC.AXLE} * 1.78 / {CALC.TIRE}"
*CLC-00-103
rpm 0 8000 0.0 "{SAE.VSS.mph} * 336 * {CALC.AXLE} * 1.30 / {CALC.TIRE}"
*CLC-00-104
rpm 0 8000 0.0 "{SAE.VSS.mph} * 336 * {CALC.AXLE} * 1.00 / {CALC.TIRE}"
*CLC-00-105
rpm 0 8000 0.0 "{SAE.VSS.mph} * 336 * {CALC.AXLE} * 0.74 / {CALC.TIRE}"
*CLC-00-106
rpm 0 8000 0.0 "{SAE.VSS.mph} * 336 * {CALC.AXLE} * 0.50 / {CALC.TIRE}"
# ==============================================================================
*PRN - Parameter Reference Numbers
# --------------------------------
# See sae_generic.txt for more information on the *PRN section
#
#Code PRN SLOT Units System Description
#------------------------- ---- ------------ ---------------- ---------------- ------------------------------------------
CALC.TIRE F080 CLC-00-080 inch Testing "Tire diameter"
CALC.AXLE F090 CLC-00-090 factor Testing "Axle Ratio"
CALC.TIS_1ST F101 CLC-00-101 rpm Testing "Trans Input Speed 1st Gear"
CALC.TIS_2ND F102 CLC-00-102 rpm Testing "Trans Input Speed 2nd Gear"
CALC.TIS_3RD F103 CLC-00-103 rpm Testing "Trans Input Speed 3rd Gear"
CALC.TIS_4TH F104 CLC-00-104 rpm Testing "Trans Input Speed 4th Gear"
CALC.TIS_5TH F105 CLC-00-105 rpm Testing "Trans Input Speed 5th Gear"
CALC.TIS_6TH F106 CLC-00-106 rpm Testing "Trans Input Speed 6th Gear"
Of course, if you have other calc pids in your existing calc_pids.txt, you need to copy the 3 sections above (colour coded) to your calc_pids.txt without disturbing your existing definitions.
Edit History:
0. initial post.
1. changed MPH to RPM.
2. changed SAE.VSS to SAE.VSS.mph.
3. changed gauge/chart high to 8000.