Results 1 to 3 of 3

Thread: B3701 Injector pulse width voltage adjustment

  1. #1
    Senior Member
    Join Date
    Jan 2005
    Posts
    155

    Default B3701 Injector pulse width voltage adjustment

    Injector Offset vs. Volts vs. Vacuum on my excel spreadsheet with Injector Flow Rates:
    is this the same as B3701 Injector pulse width voltage adjustment?

    If so, it's 90*s out with kPa at the top instead of vertical. The vertical on the spread sheet appears to be the volts 4.5 to 20.5 the horizontal at the top is -80 to 80
    There are three of these charts, #2 goes from 20 to 180 and #3, the range is 128 to 640. It only has the above title and no lables.

    Any one knowledgeable about this and could you please enlighten me.

    Also, I tried to attach this spread sheet to this message with manage attachments and I flunked the test. Again!

    I thought this spread sheet with ten different injector flow rates and all associated information would be of use to others.

    Thanks, Curt
    Last edited by curtbriggs; December 16th, 2010 at 06:16 AM.
    99C5, mn6, Vortec T trim, Snow meth injection, AFR 205s, ARP studs,Comp 224*112*+2*.580", YellaTerra RRs, PRC Ti's w/dbls, Supermaxx LTs, No Cats, Corsa Indys, LS6Intk, Hurst, Fikse Aro18"s. Pilot Sports 315/30,265/35, 04ZO6 Shocks Hotchkis bars, EBC YellowStuff pads, SS hoses, LM-1, EFILive, 2002 OS. RPS dual disc Clutch, DTE Strut Brace & output shaft.

  2. #2
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Hi Curt,

    You can zip up the file(s) (make a Windows compressed folder) and then try posting the zip file.

  3. #3
    Lifetime Member 5.7ute's Avatar
    Join Date
    Oct 2006
    Posts
    1,840

    Default

    Curt. In the Efilive tune tool there is a conversion tool. Copy with labels B3701. Then open the conversion tool, make a map to replicate the B3701 table (dont have efilive here at work any more but there is a create labels button or similar that will do it for you) hit the transpose tab which will change the axis, copy & paste from your spreadsheet to this table. Hit transpose again to get the units back to efilive format & then copy & paste with labels this back to your tune.
    The Tremor at AIR

Similar Threads

  1. (B3701) Injector Pulse Width values for SVO 42# Injectors
    By DrkPhx in forum General (Petrol, Gas, Ethanol)
    Replies: 0
    Last Post: September 13th, 2009, 01:56 AM
  2. injector pulse width max?
    By pero648 in forum Gen III V8 Specific
    Replies: 4
    Last Post: April 5th, 2008, 11:47 AM
  3. Small Pulse Adjust/Low Pulse Width Injector Offset
    By N0DIH in forum General (Petrol, Gas, Ethanol)
    Replies: 0
    Last Post: September 4th, 2007, 08:05 AM
  4. Injector pulse width
    By Bruce Melton in forum General (Petrol, Gas, Ethanol)
    Replies: 5
    Last Post: October 7th, 2006, 12:49 PM
  5. Minimum Injector Pulse Width
    By curtbriggs in forum General (Petrol, Gas, Ethanol)
    Replies: 11
    Last Post: May 11th, 2006, 10:28 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •