BB Logging beta update: April 07, 2008

[ScarabEpic22]

I just updated my V2, and after I copy the P10_A.pmm and P10_M.pmm (BTW GM never released a manual for the P10 FWIW) I get nothing in the F1 Select Vehicle section. Tried copying the LS1B_A.pmm and still get nothing. However, I dont have my V2 connected to my TrailBlazer, dont know if Im allowed to select before Im connected or not. Im using internal memory, no SD card handy.

Oh, and the bootblock/firmware upgrade took less than a minute and was flawless on my end. Can copy files to/from easily too.

[Blacky]

I just updated my V2, and after I copy the P10_A.pmm and P10_M.pmm (BTW GM never released a manual for the P10 FWIW) I get nothing in the F1 Select Vehicle section. Tried copying the LS1B_A.pmm and still get nothing. However, I dont have my V2 connected to my TrailBlazer, dont know if Im allowed to select before Im connected or not. Im using internal memory, no SD card handy.

Oh, and the bootblock/firmware upgrade took less than a minute and was flawless on my end. Can copy files to/from easily too.

Are you copying the Options.ini file to the [Config] tab page? I've been caught a few times copying it to the [Scan] or [Tune] tab pages - that will cause no vehicle options to show up.

You don't need to be connected to select a vehicle - so long as the Options.ini file is in place.

Glad the boot block update worked. Two have failed so far. I won't know what the problem was until I get them back here for dissection.

Regards
Paul

[bballer182]

I went to update to the latest release and after selecting Boot Block version FSBootV2_05_06(0407), I checked the Bootblock box and push program.

i got an error that I think was 0101 and now the V2 just has the two orange LED flashing back and forth.

HELP!

I think I'm in the same boat as this guy. Is there any way to recover? Explorer does not see it being connected.

HELP!

[joecar]

From EFILive Explorer, Date/Time tab, doing Set Date/TIme or Set Now spins for a few moments and then comes back with Error $0101.

Can you capture/save a trace (*.rtf) from EFILive_Hapi that shows the coms after you click on the time button?

Paul, here is the trace file attached...
.

[joecar]

My PCM emitted DTC P0420...

I read it ok with V2 BBL, saved all diagnotics to file (see attached)... FF1 seems to be a copy of FF0.

The FF's in the attached file contain a line that says "$119E=$8B".

Then I went to clear DTC's and V2 said "Error $0281"...
the MIL went out at the same time...
I went to reread the DTC's but they were cleared, so V2 must have cleared the DTC.

Edit: I corrected my typos.

[joecar]

- Page up/down (using left/right arrows) works good.
- Units for EQ ratio has been fixed ("EQR").
- logged DYNCYLAIR_DMA shows up in the scantool.



Edit: I added the 3rd line.

[joecar]

FUELSYS logged correct value ok on V2, but scantool shows value "unknown" thru-out.

FTC is ok.

Scantool still shows [Manual] for LS1B_A logs from V2.

[joecar]

The LED's don't seem to do what the the alarm bits specify, altho the alarm sounds ok.

; Alarm: Is 5 ":" seperated fields:
;        min:   Minimum value, below which the alarm will sound.
;        max:   Maximum value, above which the alarm will sound.
;        style: Is one of:
;                0 = No sound, No LEDs
;                1 = Low pitch
;                2 = Medium Pitch
;                3 = High Pitch
;                4 = Very high Pitch
;               16 = Illuminate LED 1
;               32 = Illuminate LED 2
;               48 = Illuminate LED 3
;               64 = Illuminate LED 4
;              128 = Illuminate LED 5
;               Add Pitch and LED values together to enable audio and visual alarms.
;               For example, for Medium Pitch and LED 4, use 2+64 = 66
;        time:  Time (in 10ms increments) for which alarm will be sounded.
;        hold:  Time (in seconds) for which the displayed value will be frozen (not implemented yet).

[JAY4SPEED]

Paul,

I performed the most recent bootblock and firmware update flawlessly. However, I keep getting error $0194 when copying to the config file in efilive explorer for BB logging. I format under the config files tab as usual after a firmware update. I select all the files in the explorer tree under efilive/V8/EFILive_Hapi/Config and drag them all into the bottom window. Everything is fine until it tries to copy T43-A.pmm and then it flashes error $0194. I've attached a trace file. Thanks for any help.

Jay

[joecar]

Paul, I edited post #25 to correct typos.