BB Logging beta update: April 07, 2008

[Blacky]

I have fixed a number of connection/detection issues in the latest update. Hopefully I can release it by Sunday night.

Please try again with the new software to see if those problems are resolved.

Regards
Paul

[mr.prick]

when will BEN factor be available with external WBO2?

[Blacky]

It is now.

Use the attached sae_generic.txt file.

The PIDs are called:
CALC.BEN1 "BEN Factor Bank 1, Serial Wideband, LS1 style"
CALC.BEN2 "BEN Factor Bank 2, Serial Wideband, LS1 style"
CALC.BEN1_B "BEN Factor Bank 1, Serial Wideband, LS2 style"
CALC.BEN2_B "BEN Factor Bank 2, Serial Wideband, LS2 style"
CALC.BEN1_E38 "BEN Factor Bank 1, Serial Wideband, E38 style"
CALC.BEN2_E38 "BEN Factor Bank 2, Serial Wideband, E38 style"

P.S. Thanks to Chad (from GreenLight Motorsports) for setting up the sae_generic file with the correct analog and serial wideband PIDs and BEN factor PIDs for E38.

Regards
Paul

[Lennart]

While transferring logged files to the PC I noticed that the transfer is rather slow.....not sure if it is supposed to be that way but a 1.5Mb file took about 30secs. to transfer.

[mr.prick]

It is now.

Use the attached sae_generic.txt file.

The PIDs are called:
CALC.BEN1 "BEN Factor Bank 1, Serial Wideband, LS1 style"
CALC.BEN2 "BEN Factor Bank 2, Serial Wideband, LS1 style"
CALC.BEN1_B "BEN Factor Bank 1, Serial Wideband, LS2 style"
CALC.BEN2_B "BEN Factor Bank 2, Serial Wideband, LS2 style"
CALC.BEN1_E38 "BEN Factor Bank 1, Serial Wideband, E38 style"
CALC.BEN2_E38 "BEN Factor Bank 2, Serial Wideband, E38 style"

P.S. Thanks to Chad (from GreenLight Motorsports) for setting up the sae_generic file with the correct analog and serial wideband PIDs and BEN factor PIDs for E38.

Regards
Paul

i selected the PID but see no data in the software.
it says N/A.
i also added CALC.BEN1 to the cal.link.txt

[mr.prick]

^
this was resolved with a re-boot of the software.
i am also getting this

Error code: ERR_PKTSTALL/75
Starting Dynamic scan mode stalled, please retry.

when i pause/stop logging/recording
then attempt to re-start logging/recording.
persistent attempts to record sometimes overcome this.

there are times when after selecting my controller (99+LS1)
it reverts to the V2 as the selected controller.
also my maps cleared from the map tab and i needed to re-install them.

i will add that the serial connection for the WBO2 is
a lot steadier and accurate than the analog connection
and after connecting (though difficult at times) there
are no problems keeping connected.

[hymey]

# Serial Wide Band BEN factors
# =============================
*CLC-00-996
factor 0.0 2.0 .1 "{EXT.WO2AFR1}/{E38.AFRATIO_DMA}"
*CLC-00-997
factor 0.0 2.0 .1 "{EXT.WO2AFR2}/{E38.AFRATIO_DMA}"

To save reading through. These are the pids for e38 ben.

[joecar]

While transferring logged files to the PC I noticed that the transfer is rather slow.....not sure if it is supposed to be that way but a 1.5Mb file took about 30secs. to transfer.

I noticed same.

[Cougar281]

I noticed same.

As did I, in the firmware one or two releases ago, I think, which I posted about.

[hymey]

Its always slow for that size file.