Results 1 to 5 of 5

Thread: flashing E38 ECU...bringing together BCM, Cluster for GEN IV conversion

  1. #1
    Senior Member
    Join Date
    Apr 2008
    Posts
    197

    Default flashing E38 ECU...bringing together BCM, Cluster for GEN IV conversion

    Hi folks, I am new in this forum and new to the EFI live world.. so pls be a little patient with me :-)

    I am electronic engineer working for Bosch rexroth in germany ( not car stuff but close loop controls for hydraulic applications..) . I own a 1997 which I will convert to he latest GEN IV engine. I bought a 5.3 out of a '07 yukon with flex fuel option. I opted for all parts, as engine harness incl ECU, BCM, instrument cluster incl wiring, fuel pump assembly...
    Problem is the components came from different donor vehicles ( all '07) . I will have to flash the ECU , BCM ... to work together in this conversion. I will have to use the latest tunes for the E38 ECU to give proper E85 performance, I also read somewhere that the active fuel management was updated a few times.
    So ok now a few questions..
    Is the flash scan V2 the right tool for the job? Is this forum the right place to get the latest tunes I would need for my project? Is I live in germany and visit the US only once or twice a year I will have problems to find proper support at home.
    any suggestions, comments will be very very welcome..

  2. #2
    Forum tyhee Site Admin GMPX's Avatar
    Join Date
    Apr 2003
    Posts
    12,732

    Default

    Where you expecting the BCM to also work in your existing vehicle? I'm not so sure that a 2007 BCM is going to work with all your existing 1997 modules (cluster, climate control etc).
    One of the issues you will have is the E38 ECM has no classII data bus, your 1997 vehicle will no doubt be ClassII, maybe the BCM will do the conversion from CAN > VPW, I am not sure.

    Cheers,
    Ross
    Need official EFILive help, please go here.
    For tuning support please post your questions on this forum (or other auto forums).
    Sorry if I don't respond to your PM, don't take it personal.


  3. #3
    Senior Member
    Join Date
    Apr 2008
    Posts
    197

    Question Gen IV conversion issues

    Ok, the preparation od the project takes more time than expected. I am still waiting for my engine. ..
    As for the BCM question: I intend to use the '07 BCM and the '07 cluster. This should work so far...I should be able to have speedo, voltage, oil pressure, rpm and temp right away. also the driver information system should work.
    As for the AC I will use a "workaround" for the beginning.
    Then there are several warning lights of the non CAN '97 system to address: antilock, airbag,... the first idea here is to use the '97 systems and built some lights either into the '07 cluster (not CAN driven of course..)or built a second warning light unit which would work for the beginning.

    More interesting is how to tell the BCM that a few CAN units are missing in this application as '07 antilock, airbags, anti theft and such.... does anybody have some ideas on this matter?

    Harald

    If nobody has done it before, somebody has to do it....

    1997 Tahoe 2dr 4WD
    2002 Alfa Romeo Sportswagon 2.0 JTD
    1982 Deutz Intrac 2004A
    2003 friesian Horse " Henry"

  4. #4
    Lifetime Member
    Join Date
    Jan 2007
    Posts
    293

    Default

    I have heard of cases where a Corvette owner had active computer controlled shocks. He changed his shocks and the computer did not like it at all. He did research and found out this option could be "turned off" with a Tech2.

    Maybe this is an option for you? The only problem is that this isn't routine procedure so the dealer may have to be coached or alerted that you can do this.

  5. #5
    Lifetime Member ChipsByAl's Avatar
    Join Date
    Feb 2006
    Posts
    581

    Default

    When a BCM is setup, it is necessary to select specific options. Take note, you cannot remove any options you want. You may need to choose between standard a/c and climate control. In either case the BCM will be expecting to talk to an a/c module.
    AL
    "Trash that carb and get Injected!"

Similar Threads

  1. gauge cluster message
    By FH Leader in forum Duramax 06 LLY / 06+ LBZ & LMM
    Replies: 14
    Last Post: March 10th, 2011, 07:11 AM
  2. Cluster Message
    By L31Sleeper in forum General (Petrol, Gas, Ethanol)
    Replies: 8
    Last Post: May 30th, 2010, 08:31 PM
  3. VY HSV instrument cluster shift light
    By Biggsy in forum General (Petrol, Gas, Ethanol)
    Replies: 3
    Last Post: July 10th, 2009, 10:21 PM
  4. Changing Mileage in New Gauge Cluster
    By Ninety8C5 in forum Lounge
    Replies: 0
    Last Post: July 5th, 2009, 11:39 AM
  5. cluster question
    By justin123 in forum Gen III V8 Specific
    Replies: 0
    Last Post: June 1st, 2009, 12:19 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •