Page 2 of 2 FirstFirst 12
Results 11 to 19 of 19

Thread: Converting 1996 PCM to '98+ or 0411?

  1. #11
    Lifetime Member Aloicious's Avatar
    Join Date
    Nov 2007
    Posts
    453

    Default

    Quote Originally Posted by Lextech View Post
    Hey KAZ,

    The 0411 will run the stock poppets just fine!

    Jeff
    yup, I ran the 411 with the stock poppets for about 4-5 months before swapping to a MPFI intake. the 411 worked find for both
    1996 c1500 gen1e 5.7L - the "LS31", 24x CNP, LS2 coils, modified T56, 12200411PCM running COS3, zz4 cam, custom MPFI, etc. coming soon: Twin Turbos

  2. #12

    Default

    Thanks guys.

    I have a "revised" spider assembly coming the end of this week. I will be doing the assembly, PCM swap, and lower plenum gasket all in one shot.

    I appreciate all the info and responses to my question.

    I will post up when I am finished.

    -Kenny

  3. #13

    Default

    Having some issues guys. 1998 Vortec 411 PCM conversion. Motor is a 383 stroker with a whipple.

    If I leave the Express Van OS without COS3 loaded it runs fine. As soon as I load 02020003 it will not run properly. Will not take throttle input, idles rough (lean), and just plain stalls after a few seconds. If I reflash the PCM with the Express van OS only it runs fine.

    Any thoughts?

    This is about the 12th COS3 I have loaded into an LS1 based PCM and never had this issue before.

    I attached the .cal file. Very basic, but no run with it.
    Attached Files Attached Files

  4. #14
    Lifetime Member
    Join Date
    Aug 2006
    Posts
    412

    Default

    Try setting P0101,P0102,P0103 to non-emissions. Are you sure you want your B3647 table to look like that?

    Jeff
    Last edited by Lextech; May 26th, 2008 at 08:05 AM.
    98 GMC RCSB 2WD, Internally stock 305 w/Twin T-3 junkyard Turbos,4L80e,Ramjet intake,42lb.inj., 0411PCM, COS3,4675LBS w/me in it. Best Time on 5 passes-13.01@110

  5. #15

    Default

    Ok Jeff,

    I changed P0101 etc to non-emissions and moved B3647 to 0.98. It runs fine now. Normally I can start and begin setting up everything the way I had it. Why is this one different?

    Thank you sir. I was severely banging my head against the wall wondering what the hell the problem was. I really need to get a heavy bag hanging from the wall to relieve my stress from time to time and help clear my head.

    Thank much!
    -Kenny

  6. #16
    Lifetime Member
    Join Date
    Aug 2006
    Posts
    412

    Default

    Cool,
    After 117 posts, I finally got 1 right.
    98 GMC RCSB 2WD, Internally stock 305 w/Twin T-3 junkyard Turbos,4L80e,Ramjet intake,42lb.inj., 0411PCM, COS3,4675LBS w/me in it. Best Time on 5 passes-13.01@110

  7. #17
    New Member
    Join Date
    Jun 2014
    Posts
    3

    Default

    I got around to the 0411 swap in my 96. Got it running with van tune. Was wondering what pid to use to check the distributor position i cant find cam retard or cmpret in the v8 software.

  8. #18
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Look for that pid in the V7 scantool.

  9. #19
    New Member
    Join Date
    Jun 2014
    Posts
    3

    Default

    I have 7.5 software i did find it in there but it says its not supported and can only seem to flash or read data through the v8 software sense it made me update my sotware to do anything.

Page 2 of 2 FirstFirst 12

Similar Threads

  1. Converting tunes to DSP
    By rjwesleyiii in forum Duramax 06 LLY / 06+ LBZ & LMM
    Replies: 6
    Last Post: September 24th, 2010, 03:45 PM
  2. 1996 7.4 with 0411 PCM
    By GAMEOVER in forum Vortec V6/V8 Specific
    Replies: 2
    Last Post: June 5th, 2010, 12:22 PM
  3. 1996 H1 Hummer Turbo-Diesel 6.5 non-intercooled
    By GAMEOVER in forum General (Diesel)
    Replies: 16
    Last Post: December 10th, 2009, 03:40 PM
  4. 1996 Impala SS
    By arubenstein in forum General (Petrol, Gas, Ethanol)
    Replies: 11
    Last Post: October 6th, 2008, 06:21 PM
  5. 1996 Vortec 4.3 v6 - need tuning tool
    By cyndee in forum General (Petrol, Gas, Ethanol)
    Replies: 2
    Last Post: January 16th, 2006, 11:49 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •