I am all software'd and flashed up with the latest files from the downloads page. fw_02_05_19
When BBL I only get maybe 30min max. Normally 10Mb files, today with the new FW only 5Mb or around 20min
My trip is 2hrs.
Am I doing something wrong...?
I am all software'd and flashed up with the latest files from the downloads page. fw_02_05_19
When BBL I only get maybe 30min max. Normally 10Mb files, today with the new FW only 5Mb or around 20min
My trip is 2hrs.
Am I doing something wrong...?
Get EFILive in europe (http://www.efilive.eu).
2007 Escalade ESV L92 6.2L VVT.
2014 VF SV LS3 Maloo.
Hmmmmmmmmmm..... Well, interesting.....I just upgraded to the latest stuff and it seems that with E67 controllers (or maybe can controllers in general) I go logging for 10 to 15 mins and then the EFI LIVE scantool just locks up....
I'm still connected, but....the screen freezes and nothing happens.....
Anyone else??
Chuck CoW
CoW BOOSTER! Electronic Throttle Enhancement.
- CLICK HERE NOW FOR MORE INFORMATION! -
VARARAM, EDELBROCK, AMERICAN RACING HEADERS, BAER BRAKES, BORLA, EFI Live, Magnuson,
COMP Cams, PROCHARGER, PRO TORQUE, PHADT Racing, INNOVATORS WEST, and more.
I am not upgrading to the latest then if it's doing this again. :p
I am on the update before the latest and it works fine. Mine was doing this on a couple of the previous updates and Paul fixed it.
E38/T43 controllers for me.
Yeah mine was doing it on an older firmware, hence why I upgraded! :(
Not good for doing VE tables.
Paul Help! E38 here. HSV OS E Series R8
Get EFILive in europe (http://www.efilive.eu).
2007 Escalade ESV L92 6.2L VVT.
2014 VF SV LS3 Maloo.
Guys, have you checked the number of PID's you are logging? I can log for a good 25 minutes and end up with a log file of 2MB in size ( E38 ). I've also performed a few extended log sessions where I've turned the engine off and allowed the V2 to enter suspend mode, then restarted the log the next time I've driven the car. Any chances you can post a log from one of these sessions where the V2 has locked up?
Simon
Its too big to attach to the message, so you can DL it here.
This is from a 1hr45min log session
http://www.systemsup2.plus.com/BBL00047.zip
Get EFILive in europe (http://www.efilive.eu).
2007 Escalade ESV L92 6.2L VVT.
2014 VF SV LS3 Maloo.
OK, you have a PID count of 19 and a channel count of 25, so I doubt that's an issue. I usually log with 22 PID's and 34 channels with no issues. Was this a log when the V2 hung or a normal log?
I take it you have checked the Firmware version in the V2?
Simon
Latest version as noted above squire with a reformatted config file system.
The copied the files from the new 8.1.1 over and the options.ini as well
Get EFILive in europe (http://www.efilive.eu).
2007 Escalade ESV L92 6.2L VVT.
2014 VF SV LS3 Maloo.
Have you tried wiggling the main ODB-II cable to see if there is an intermittent connection? I know with mine that if I wiggle the cable just near the RJ45 plug, the V2 will reboot, indicating a bad connection. You may be getting a bad power feed into the V2, causing it to lock up.
Ringman I am using the latest release firmware version 19 same as you and have logged 500km in one day where the car was switched off twice and still got it all on 1 log. Must be something going wrong with your V2. I was logging on E 40 PIDs for Ls2.