Page 5 of 13 FirstFirst ... 34567 ... LastLast
Results 41 to 50 of 124

Thread: E38 VVE Setup Guide

  1. #41
    Senior Member alian's Avatar
    Join Date
    Jun 2008
    Posts
    140

    Default

    Quote Originally Posted by macca_779 View Post
    Don't think so mate. Due to them being a top mount Blower your forced to use a remote water heat exchanger setup. Perhaps a larger front mount and a better pump than the crappy electric one supplied would improve the efficiency but there isn't much I imagine you can do about the blower side of things.
    If I was going down the FI route I'd go Turbo's or perhaps a Procharger. The temp increase over ambient is bugger all with a good Air/Air Intercooler
    So cooling the air with an intercooler before it goes into the blowwer wont help at all??

  2. #42
    Lifetime Member GMPX's Avatar
    Join Date
    Apr 2003
    Posts
    13,148

    Default

    Quote Originally Posted by swingtan View Post
    Hi Ross,

    I've added that in and placed it on P10, where I first describe altering the zone boundaries. I thought that as people would be looking at the table then, it would be a good place to get them to check. I used a different PDF converter which increased the size a little, but it's still well under 1MB.

    Simon
    Thanks Simon, I've uploaded this newer version to the downloads section on the website.

    Cheers,
    Ross
    I no longer monitor the forum, please either post your question or create a support ticket.

  3. #43
    Lifetime Member macca_779's Avatar
    Join Date
    Jan 2007
    Posts
    327

    Default

    Quote Originally Posted by alian View Post
    So cooling the air with an intercooler before it goes into the blowwer wont help at all??
    Bugger all mate. Unless you perhaps cool it with dry ice.

  4. #44
    Senior Member alian's Avatar
    Join Date
    Jun 2008
    Posts
    140

    Default

    Quote Originally Posted by macca_779 View Post
    Bugger all mate. Unless you perhaps cool it with dry ice.
    Thanks 4 that Macca, Did a bit more looking
    Cheers Ian

  5. #45
    Member
    Join Date
    May 2008
    Posts
    63

    Default e38 ben map?

    First of all great work guys this tutorial is a great help.
    Where do you find the e38 ben map?Is it a preconfigured map or do i have to write it up?.If i have to make it do you use the normal kpa/rpm ben factor or something different. How do you apply the ben factors to the vve table .You say not like the ls1 so im a little lost?
    Also when logging my autronic wide band it always reads .4 richer than the scantool indicates any way of correcting this?
    Cheers shane
    Last edited by shane; March 25th, 2009 at 11:40 PM.

  6. #46
    Junior Member
    Join Date
    Oct 2007
    Posts
    20

    Default

    thanks I can use this.

  7. #47
    Lifetime Member minytrker's Avatar
    Join Date
    Jan 2006
    Posts
    1,332

    Default

    When I adjust B8021 it doesnt change B8021? What am I missing? When I go back and paste its the exact same.
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	VVE.jpg 
Views:	337 
Size:	156.9 KB 
ID:	6052  

  8. #48
    Lifetime Member GMPX's Avatar
    Join Date
    Apr 2003
    Posts
    13,148

    Default

    Lorenz, you need to reload the file after you save your changes. If that is omitted in the document we should revise it. The file reload is only necessary when changing the zone values (for MAP or RPM).

    Cheers,
    Ross
    I no longer monitor the forum, please either post your question or create a support ticket.

  9. #49
    Member
    Join Date
    Jul 2008
    Posts
    99

    Default

    Simon and everyone else who has had a hand in this thanks, job well done.

  10. #50
    Junior Member
    Join Date
    Mar 2008
    Posts
    49

    Default

    Thanks for the guide, great work.

    In regard to disabling LTFT I found that adjusting B1508, B1509 and B1510 was not enough.

    I also had to set B1511 and B1512 (min/max adjustment) to zero.

    Cheers.

Page 5 of 13 FirstFirst ... 34567 ... LastLast

Similar Threads

  1. E38 / E67 VATS disable guide
    By GMPX in forum E37, E38 & E67 PFI ECM's
    Replies: 141
    Last Post: March 22nd, 2023, 12:35 PM
  2. Tuning Beginners Guide
    By NASABlue in forum Gen III V8 Specific
    Replies: 0
    Last Post: September 30th, 2009, 01:37 AM
  3. Beginners guide to tuning
    By ringram in forum Tutorials
    Replies: 26
    Last Post: June 17th, 2006, 09:46 PM
  4. Draft LC-1 Guide
    By 98WS6_JPM in forum General
    Replies: 4
    Last Post: May 12th, 2006, 01:53 AM
  5. PCM tuning guide
    By 2000ssnb in forum General (Petrol, Gas, Ethanol)
    Replies: 2
    Last Post: September 3rd, 2004, 04:42 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •