Page 1 of 3 123 LastLast
Results 1 to 10 of 27

Thread: serial port cable that goes to v2

  1. #1
    Member
    Join Date
    Mar 2007
    Posts
    64

    Default serial port cable that goes to v2

    does any one have a diagarm to make the serial cable for the v2 with the 9 pin serial port to the 6 pin phone jack looking connector. hope i am explaining correctly.thanks

  2. #2
    Lifetime Member GMPX's Avatar
    Join Date
    Apr 2003
    Posts
    13,148

    Default

    You should have got one with your V2. It would be easier (and cheaper) to order one through one of our resellers, we don't try to make money on spare cables, it more to cover costs and provide a replacement service.

    Cheers,
    Ross
    I no longer monitor the forum, please either post your question or create a support ticket.

  3. #3
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    Cable wiring diagram (for LC-1): FlashScan-to-LC-1-Serial-Cable-Diagram

    Your V2 came with a DB9 serial cable...
    Your wideband came with a DB9 serial cable...
    You need a null-modem adapter (orange item in pic below)... [it has to be a null-modem adapter and not just a gender bender].


    To enable serial AFR in the V2, see here: Tutorial-FlashScan-V2-Serial-Wideband-Logging


    You also have to remember to plug the null terminator plug (blank 2.5mm stereo plug) into the LC-1's SERIAL IN cable.


    This is the null-modem adapter: http://www.sfcable.com/cable/p/30D1-C1-S.html <-- less than $5 shipped

    Last edited by joecar; March 4th, 2014 at 12:10 PM.

  4. #4
    Member
    Join Date
    Mar 2007
    Posts
    64

    Default

    i cannot find my db9 cable but i bought a 6 pin jack and a DB9 female to RJ11. will this work?

  5. #5
    Member
    Join Date
    Mar 2007
    Posts
    64

    Default

    i found my cable. now can i connect it with a null modem adapter and cut the end off a serial cable and connect to the fjo wires?

  6. #6
    Lifetime Member mr.prick's Avatar
    Join Date
    Nov 2006
    Posts
    3,195

    Default

    ____RJ12______
    1 = Tx Data
    2 = Rx Data
    5 = Ground

  7. #7
    Joe (Moderator) joecar's Avatar
    Join Date
    Apr 2003
    Posts
    28,403

    Default

    If you can identify Tx, Rx, Gnd, then you wire them as shown in post #6 and you don't need the null-modem adapter.

    If it doesn't work, swap Tx and Rx.

  8. #8
    Member
    Join Date
    Mar 2007
    Posts
    64

    Default

    thx i will try tommorrow

  9. #9

    Default

    The AFM1500 pins are as noted;

    pin #1= Rx
    pin #2=Tx
    pin #3=Grnd

    According to the AFM1500 manual;

    DB9 Female (to PC)
    Terminal Number
    #2 (Rx) to pin #1 of module (male)
    #3 (Tx) to pin #2 of module (male)
    #5 (Gnd) to pin #6 of module (male)


    I assume "to module" is the AFM1500 box and the "to PC" is the feed heading to the V2??

    Trying to reason through the null modem conversion. Ughh!

    Howard
    Last edited by Redline Motorsports; November 28th, 2009 at 04:49 PM.

    www.redline-motorsports.net

    1-954-703-5560

    2006 ZO6 895/866 with APS TT
    2010 SSRS Camaro HTR-900TT (798/801)
    2011 HTR-850R Camaro
    2012 ZL1 Auto (10.33@135 MPH) Video Here!

  10. #10
    Lifetime Member mr.prick's Avatar
    Join Date
    Nov 2006
    Posts
    3,195

    Default

    Are you trying to bypass a Null Modem?

    RS232 serial cables pinout
    512k RoadRunner Firmware 12.14R
    FlashScan V2 Bootblock V2.07.04 Firmware V2.07.22 EFILive V7.5.7 (Build 191) V8.2.1 (Build 181)
    LC-1 WBO2

    _________________________________________________

Page 1 of 3 123 LastLast

Similar Threads

  1. Flashscan to LM-2 Serial Cable
    By TAQuickness in forum FlashScan V2 BB Logging
    Replies: 19
    Last Post: May 2nd, 2016, 09:36 AM
  2. FlashScan to LC-1 Serial Cable Diagram
    By Blacky in forum FlashScan V2 BB Logging
    Replies: 5
    Last Post: November 26th, 2009, 06:50 AM
  3. Tried making own Serial Wideband Cable, HELP!!
    By edwardzracing in forum FlashScan V2
    Replies: 11
    Last Post: March 18th, 2009, 03:54 AM
  4. fjo serial cable questions..please help
    By articSS in forum Black Box Logging
    Replies: 7
    Last Post: October 28th, 2008, 02:05 PM
  5. Calibrating AD port
    By stigmundfreud in forum Black Box Logging
    Replies: 5
    Last Post: March 30th, 2008, 11:21 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •