I am connecting to an LMM Duramax ECM. When I goto dashboard the default gauge page shows the gauges but not working like not reading anything. If i hit the yellow button on the dashboard section I get the following error. Now I have activated the DVT and they work at this same point so it seems connected to me since I raise and lower engine RPM from the DVT. I have installed the latest
EfiLive 7.5.5 build 77
EfiLive Explorer 8.1.2 build 44
Bootblock 2.06.02
Firmware 2.06.06
Now it has worked before but that was before the last update. I had build 7.5.5 build 72 and 8.1.* build 42 and worked for me then on same notebook and usb port.
This a portion of the error log.
Code:
Error report generated by EFILive at 18:02:38 on Dec 29, 2008
Error code: ERR_IGNORED/4
No response from vehicle.
EFILive Version: 7.5.5 (Build 77)
Platform: Windows NT
Version: 6.0 (build 6001)
Processor type: Pentium 2261MHz
Directories
Temporary Cache: C:\Users\crusher65\Documents\EFILive\V7.5\Temporary cache
Logged Data: C:\Users\crusher65\Documents\EFILive\V7.5\Logged data
Customers: C:\Users\crusher65\Documents\EFILive\V7.5\Customers
Configuration: C:\Program Files\EFILive\V7.5\Configuration
Exported Data: C:\Users\crusher65\Documents\EFILive\V7.5\Exported data
Images: C:\Users\crusher65\Documents\EFILive\V7.5\Images
Sounds: C:\Users\crusher65\Documents\EFILive\V7.5\Sounds
Maps: C:\Users\crusher65\Documents\EFILive\V7.5\Maps
Pids: C:\Users\crusher65\Documents\EFILive\V7.5\PIDs
Virtual Dash: C:\Users\crusher65\Documents\EFILive\V7.5\VDash
Print Reports: C:\Users\crusher65\Documents\EFILive\V7.5\Print reports
Bug Reports: C:\Users\crusher65\Documents\EFILive\V7.5\Bug reports
Connected: No
Com port: 0
Com setup: EFILive FlashScan V2.5: USB
Requested baud rate: 115200
Cable id: 7
Cable code: FlashScan V2
Cable desc: EFILive FlashScan V2
Cable version: 2.6.6
Cable Firmware date: 20081214
Cable model: FSV2
Cable Serial number: 003684136154
Protocols: 0
Protocol list:
Auto connect: No
Scan OBDII info: No
Error retries: 1
Retry delay: 10
Message throttle: 0
Most recently used VIN: 1GCHK236X7Fxxxxxx (Note: 1)
PCM information
Hardware Number: Unknown
Calibration ID: 12617102
Serial Number: 86J701301280
Operating System: 12628596
Not used: 12628594
Not used: 12628713
Transmission: 12628594
Not used: 12628702
Not used: 12628695
Not used: 12628694
Not used: 12628715
Operating System BCC: YRLF
Stream-Slow scan mode: Supported
Stream-Fast scan mode: Supported
Maximum dynamic packets: 16
Detected modules:
Selected parameters:
CALC.G_FORCE=1,4286
CALC.POWER_RW=1,4300
GM.BALRCYL1=1,4401
GM.BALRCYL2=1,4402
GM.BALRCYL3=1,4403
GM.BALRCYL4=1,4404
GM.BALRCYL5=1,4405
GM.BALRCYL6=1,4406
GM.BALRCYL7=1,4407
GM.BALRCYL8=1,4408
GM.BAROV=1,4411
GM.BOOST2_DMA=1,4415
GM.EGT2A=1,4481
GM.FLS=1,4555
GM.FRPCOM=1,4563
GM.FRPDES=1,4565
GM.FRPSV=1,4566
GM.IAT2=1,4620
GM.MAIN1Q_DMA=1,4689
GM.MAIN1T_DMA=1,4690
GM.MNINJTIM=1,4733
GM.PILOT2T_DMA=1,4780
GM.TCVPOS=1,4839
GM.WIFV=1,4902
SAE.BARO=1,4913
SAE.ECT=1,4928
SAE.FLI=1,4935
SAE.FRP_C=1,4938
SAE.IAT=1,4941
SAE.MAF=1,4946
SAE.RPM=1,4967
SAE.VSS=1,4983
Thanks for your time and help.
Brian