Ok, I have FlashScan V2 updated to the latest bootblock & firmware. Thanks for the upgrade PDF, but it was a bit lacking in details, so I'm including exactly what I did so that others won't have to figure a couple of things out along the way like I had to.
01. Installed 7.5 & 8.2 into the same directory (per upgrade PDF)
02. Started Scan 7.5 & selected 'Connect to vehicle'
03. Selected 'OK' when prompted for controller (default: 'FlashScan/Autocal Only')
04. The following was generated in the console (F6) section:
18:39:43.659: EFILive V7.5 Version V7.5.7 (Build 211)
18:39:53.331: Ready.
23:10:49.402: Scanning for EFILive FlashScan V2 HAPI
23:10:49.447: Autodetect interface ...
23:10:50.932: Interface not detected
23:10:51.580: Scanning for EFILive FlashScan V2 USB
23:10:51.601: Autodetect interface ...
23:10:51.777: Interface firmware version: 2.4.65
23:10:51.791: Connection to [FS2] interface is OK
23:10:51.841: Interface firmware model: FS2
23:10:51.871: Interface firmware model: FS2
23:10:51.899: Interface firmware version: 2.4.65
23:10:51.927: Interface firmware date: Oct 02, 2007
23:10:51.960: FlashScan serial number: <removed>
23:10:51.992: FlashScan license number: <removed>
23:11:29.881: Validating PIDs...
23:11:34.243: Initialising PIDs...
23:11:35.307: Initialising Modules...
23:11:35.336: Ready.
05. Closed EFILive Scan 7.5
06. Opened EFILive Firmware Programmer
07. Selected '...' button in the 'Update FlashScan V2' section
08. Selected 'FSProg_V2_4_72.ffw' (NOT .efw as the upgrade PDF states) & selected the 'Open' button
09. Selected the 'Program' button to update the firmware to 2.04.72 (step A1 from upgrade PDF)
10. Used FlashScan's menu option to upgrade boot block to 2.05.08 (step A2 from upgrade PDF)
Here's where I wound up being stuck for a few minutes, as FlashScan appeared to be in dead-poll mode (two alternating orange LEDs blinking). However, the EFILive Firmware Programmer would not let me update the firmware to 2.05.21, it refused to acknowledge that FlashScan was in dead-poll mode. By the way, I had to rename the 2.05.21 file extension to .ffw for the EFILive Firmware Programmer to allow it to be visible as a selection. Anyway, this was a dead end, so I continued as follows.
11. Opened EFILive Explorer 8.2 in order for the EFILive Control Panel to appear in the taskbar system tray
12. Opened EFILive Control Panel
13. Selected 'F6: Firmware'
14. Boot block was showing as 2.05.08 and warned that the firmware needed to be updated
15. Updated firmware in the CP to 2.05.21 (step A3 from upgrade PDF)
16. Updated boot block in the CP to 2.07.04 (step D1 from upgrade PDF)
17. Updated firmware in the CP to 2.07.35 (step D2 from upgrade PDF)
18. Both the boot block version and firmware version were then listed in the CP as OK.
Done. I verified that the VIN license was still active in FlashScan and I should be good to go now. Thanks for the response and the information, joecar.
On to the next 'from scratch' document.