Oh your a good man!Originally Posted by Blacky
update worked, sorta, LB7 definately readable now, have not gotten to an LLY yet. But did get to a 2003 LS1 gasser in a truck and it failed as follows
19:18:39.562: Scanning for EFILive FlashScan V2 USB
19:18:43.265: Scanning for EFILive FlashScan V2 HAPI
19:18:43.328: CAN-VPW Bridge Actived
19:18:43.359: Current protocol set to: "SAE J1850 VPW"
19:18:43.421: Interface firmware version: 9.5.2
19:18:43.468: Interface firmware model: FSV2
19:18:43.500: Interface firmware version: 9.5.2
19:18:43.515: Interface firmware date: Nov 28, 2007
19:18:43.546: FlashScan serial number: 003597229256
19:18:43.578: FlashScan license number: 0000003597229256
19:18:43.609: Disconnecting ...
19:18:43.656: CAN-VPW Bridge Deactived
19:18:43.703: Disconnected
19:18:44.343: Scanning for EFILive FlashScan V2 USB
19:18:48.046: Scanning for EFILive FlashScan V2 HAPI
19:18:48.218: CAN-VPW Bridge Actived
19:18:48.250: Current protocol set to: "SAE J1850 VPW"
19:18:48.328: Interface firmware version: 9.5.2
19:18:49.453: Current protocol: "SAE J1850 VPW"
19:18:49.500: Interface firmware model: FSV2
19:18:49.515: Interface firmware version: 9.5.2
19:18:49.546: Interface firmware date: Nov 28, 2007
19:18:49.562: FlashScan serial number: 003597229256
19:18:49.593: FlashScan license number: 0000003597229256
19:18:49.718: Getting status...
19:18:49.781: Status: OK.
19:18:50.750: Bootloader version: LS1B_v1.6R (04D2-6318)
19:18:50.750: Preparing PCM for reading flash...
19:18:50.796: PCM seed is: $2584
19:18:50.796: Unlock attempt 1 of 1
19:18:50.953: Initializing PCM...
19:18:51.718: Initializing PCM, step 1 of 4
19:18:51.718: Initializing PCM, step 2 of 4
19:18:52.500: Initializing PCM, step 3 of 4
19:18:54.046: Initializing PCM, step 4 of 4
19:18:54.484: Initializing bootloader...
19:18:54.828: Initializing bootloader, step 1 of 3
19:18:55.218: Initializing bootloader, step 2 of 3
19:18:55.609: Initializing bootloader, step 3 of 3
19:18:56.109: PCM ready for reading flash.
19:18:56.250: Intel AB28F800B - 1Mb
19:19:06.171: Error: Failed. Controller has returned to normal operation, please retry the operation.
19:19:06.812: Total time: 00:09
19:19:06.812: Rebooting PCM... (please wait up to 8 seconds)
19:19:07.968: PCM has booted successfully...
19:19:08.968: Clear emisison related DTCs...
19:19:09.015: Clear DTCs for all modules...
19:19:09.875: Disconnecting ...
19:19:09.921: CAN-VPW Bridge Deactived
19:19:09.984: Disconnected
19:19:13.156: Done!
same pcm reads just fine with other interfaces that i have.
This is a protocol problem. The leading 4 digits should not be on the license number. I know what is causing it, I'll have it fixed in the next update.Originally Posted by mrrattle
Regards
Paul
Before asking for help, please read this.