BB Logging beta update: April 07, 2008

[mr.prick]

when will BEN factor be available with external WBO2?

[Blacky]

It is now.

Use the attached sae_generic.txt file.

The PIDs are called:
CALC.BEN1 "BEN Factor Bank 1, Serial Wideband, LS1 style"
CALC.BEN2 "BEN Factor Bank 2, Serial Wideband, LS1 style"
CALC.BEN1_B "BEN Factor Bank 1, Serial Wideband, LS2 style"
CALC.BEN2_B "BEN Factor Bank 2, Serial Wideband, LS2 style"
CALC.BEN1_E38 "BEN Factor Bank 1, Serial Wideband, E38 style"
CALC.BEN2_E38 "BEN Factor Bank 2, Serial Wideband, E38 style"

P.S. Thanks to Chad (from GreenLight Motorsports) for setting up the sae_generic file with the correct analog and serial wideband PIDs and BEN factor PIDs for E38.

Regards
Paul

[Lennart]

While transferring logged files to the PC I noticed that the transfer is rather slow.....not sure if it is supposed to be that way but a 1.5Mb file took about 30secs. to transfer.

[mr.prick]

It is now.

Use the attached sae_generic.txt file.

The PIDs are called:
CALC.BEN1 "BEN Factor Bank 1, Serial Wideband, LS1 style"
CALC.BEN2 "BEN Factor Bank 2, Serial Wideband, LS1 style"
CALC.BEN1_B "BEN Factor Bank 1, Serial Wideband, LS2 style"
CALC.BEN2_B "BEN Factor Bank 2, Serial Wideband, LS2 style"
CALC.BEN1_E38 "BEN Factor Bank 1, Serial Wideband, E38 style"
CALC.BEN2_E38 "BEN Factor Bank 2, Serial Wideband, E38 style"

P.S. Thanks to Chad (from GreenLight Motorsports) for setting up the sae_generic file with the correct analog and serial wideband PIDs and BEN factor PIDs for E38.

Regards
Paul

i selected the PID but see no data in the software.
it says N/A.
i also added CALC.BEN1 to the cal.link.txt

[mr.prick]

^
this was resolved with a re-boot of the software.
i am also getting this

Error code: ERR_PKTSTALL/75
Starting Dynamic scan mode stalled, please retry.

when i pause/stop logging/recording
then attempt to re-start logging/recording.
persistent attempts to record sometimes overcome this.

there are times when after selecting my controller (99+LS1)
it reverts to the V2 as the selected controller.
also my maps cleared from the map tab and i needed to re-install them.

i will add that the serial connection for the WBO2 is
a lot steadier and accurate than the analog connection
and after connecting (though difficult at times) there
are no problems keeping connected.

[hymey]

# Serial Wide Band BEN factors
# =============================
*CLC-00-996
factor 0.0 2.0 .1 "{EXT.WO2AFR1}/{E38.AFRATIO_DMA}"
*CLC-00-997
factor 0.0 2.0 .1 "{EXT.WO2AFR2}/{E38.AFRATIO_DMA}"

To save reading through. These are the pids for e38 ben.

[joecar]

While transferring logged files to the PC I noticed that the transfer is rather slow.....not sure if it is supposed to be that way but a 1.5Mb file took about 30secs. to transfer.

I noticed same.

[Cougar281]

I noticed same.

As did I, in the firmware one or two releases ago, I think, which I posted about.

[hymey]

Its always slow for that size file.

[Blacky]

I just tested the coms on a Vista SP1 machine.

Copy to FlashScan (SD card) 1.75Mb 21.7 seconds 632 kbps.
Copy from FlashScan (SD card) 1.75Mb 19.5 seconds 696 kbps.

Is anyone seeing anything significantly different that this?

Note: The Trace option in EFILive_Explorer shows the time to transfer and the average transfer speed achieved.

Also, make sure you have tracing turned off in EFILive_Hapi.exe. On slower computers that can be a time waster during transfers.

Regards
Paul