BB Logging beta update: April 14, 2008

[POLARIS_600cc]

Wow this thread is a mess to follow
It's quite odd that the disables have no immediate effect. Out of interest, can you try the idle speed control (and VNT too as well I guess) whilst you are not logging at the same time. Perhaps some messages are just not getting through whilst logging at the same time. Not suggesting this is the solution, just curious to see if it cures the intermittent response from the ECM.

Thanks,
Ross

Just thought I would let you know I was playing around with the DVT controls and there was no delay for me. Also I was messing with idle speed and vnt position at the same time and both worked. I did not try idle speed and rail pressure changes together. I also was not logging any of this. My truck is an 06 LBZ


EDIT: I also just noticed I have @hotmail.com in my username, since your an admin could you pm me with info on how to take that out, or feel free to just do it. Thanks.

[mr.prick]

when will we have the ability to select
how logged data is applied with RTACS,
other than multiply?
http://forum.efilive.com/showpost.ph...68&postcount=1
sorry to nag at this topic again.

FWIW
i`ve had no problems since this last update.

[GMPX]

Just thought I would let you know I was playing around with the DVT controls and there was no delay for me. Also I was messing with idle speed and vnt position at the same time and both worked. I did not try idle speed and rail pressure changes together. I also was not logging any of this. My truck is an 06 LBZ


EDIT: I also just noticed I have @hotmail.com in my username, since your an admin could you pm me with info on how to take that out, or feel free to just do it. Thanks.

Thanks for the feedback, I removed the @hotmail from your name, you might need to clear the cookie to log back in, see how you go.

Cheers,
Ross

[GMPX]

I agree, but at the moment we don't have a proper tracking system for bugs / issues found with the BBL beta releases. I guess you "could" set up a proper logging and tracking system, but that would just take your time away from releasing the next update......

Simon.

Trust me, I'd be happy to play with vBulletin admin all day, stress free work sounds good. But you are right, things are probably getting missed.

Cheers,
Ross

[swingtan]

What is the operating system of the ECM that you are logging?
Regards
Paul

Paul, RE: the AFR reading being off. Forget this one as I just realised what I did. I think I selected an E40 controller instead of E38.......... Funny that it seemed to work so well actually.

Sorry for the side track......

Simon

[Black02SS]

Was able to test Serial for LM-1 and LOVE it. Can't wait for the FJO to be supported. It is simply awsome. Only issue I saw was the values actually went past 20.9 on decel up to 120:1.1 AFR. Made the BEN show 6.0. LOL

Make sure you turn DFCO off when logging bens.

I understand that but the values should have a min and max limits that Live shows. ie. 0.0-20.9

[Blacky]

when will we have the ability to select
how logged data is applied with RTACS,
other than multiply?
http://forum.efilive.com/showpost.ph...68&postcount=1
sorry to nag at this topic again.

FWIW
i`ve had no problems since this last update.

It is implemented in the current beta software.
Quote from the release notes: EFILive beta V7.5.4 (Build 44)

RTACS now supports Addition, subtraction, multiplication and division as well as the current BEN factor percentage adjustment. Just add the operator (+, -, * or /) you wish to use followed by a comma before the first PID name in the *.RRR key like this: Bxxxx.RRR=+,<pidname> Leave it blank to use the standard BEN factor %.

Regards
Paul

[Blacky]

I understand that but the values should have a min and max limits that Live shows. ie. 0.0-20.9

Hmmm, the max should be 25.00AFR (1.701 lambda). I will check why it is going above that value.

Regards
Paul

[Lennart]

Wow this thread is a mess to follow
It's quite odd that the disables have no immediate effect. Out of interest, can you try the idle speed control (and VNT too as well I guess) whilst you are not logging at the same time. Perhaps some messages are just not getting through whilst logging at the same time. Not suggesting this is the solution, just curious to see if it cures the intermittent response from the ECM.

Thanks,
Ross

I tried that already....logging or not does not make a difference. Just logged it for you to see :-)

[ringram]

Had an issue where a log file was corrupt and only 2kb in size. It should have been around 8-9Mb.

Other than that all is well. It would be good if you could indicate a default pid selection in the .ini file so you didnt have to manually select it each time. Kind of go straight to record..