where do you get the new firmware, I have v12.13-R.
where do you get the new firmware, I have v12.13-R.
it`s supposed to be here
http://www.moates.net/documentation....entation_id=22
but it`s not.
email Moates for it and ask him why it`s not there.
i can post it but i`m not sure if that would be acceptable or not.
Well removed the ribbon cable and fitted a mini USB cable direct to my laptop... and it still locks both the scan and tune tool if i open them with the RR plugged in... any more ideas???
I just played around with the drivers but not sure that's your issue.
Need to contact Craig I think.
Howard
YOU ONLY NEED TWO TOOLS IN LIFE - WD-40 AND DUCT TAPE. IF IT DOESN'T
MOVE AND SHOULD, USE THE WD-40. IF IT SHOULDN'T MOVE AND DOES, USE THE
DUCT TAPE.
IF YOU CAN'T FIX IT WITH A HAMMER, YOU'VE GOT AN ELECTRICAL PROBLEM.
98 K1500 'HOLDEN' Suburban.
Custom Whipple SC, Mercruiser Marine intake, 0411 PCM, 4L80E w/shift kit
Yer i think i need to try my luck with contacting Craig about this one.
What did you do with the drivers hquick?? thats really where i think the issue lies..
Its not really a huge bug as i now know what to do to avoid it happening, but every now and then when things get out of sync and i loose communictaion and it tries to reconect I get frozen programs....
You could try downloading the driver cleaner....and then re-load the drivers as per the instructions.
Seemed to work for me when mine used to lock up.
Howard
YOU ONLY NEED TWO TOOLS IN LIFE - WD-40 AND DUCT TAPE. IF IT DOESN'T
MOVE AND SHOULD, USE THE WD-40. IF IT SHOULDN'T MOVE AND DOES, USE THE
DUCT TAPE.
IF YOU CAN'T FIX IT WITH A HAMMER, YOU'VE GOT AN ELECTRICAL PROBLEM.
98 K1500 'HOLDEN' Suburban.
Custom Whipple SC, Mercruiser Marine intake, 0411 PCM, 4L80E w/shift kit
I got some bizzare results with EFILive Scan and my RR, as the RR isn't too happy at all about sharing the USB port with anything. So if you can, make sure it is on another USB port (with nothing else on it). My laptop has 4, 2 and 2, 2 on one port and 2 on the other. So if I run EFILive on the one with the RR, things get "sassy"....
Are you still having issues??
I recently upgraded software from 7.5.3(B36) to 7.5.5(B74) and have been experiencing all the same symptoms above in fact I know of others as well having the same issues.This becomes very frustrating.
I went back to software 7.5.3 and the scan/Tune & Roadrunner run faultlessly.
856RWHP 408 Supercharged LS1 Holden Commodore.
Ok is anyone else experiencing problems with the scan & tune tool with the roadrunner connected?
All my drivers etc are up todate.And I'm sure I have upgraded properly,
The only thing that I haven't done was delete the registry when upgrading from V7.5.3 to 7.5.5.
Unfortunately since the only way to exit the program is to down power the PC therefore I'm unable to provide an error report for EFILive analysis.
As previously mentioned no problems with the earlier release.
Thanks
856RWHP 408 Supercharged LS1 Holden Commodore.
I havent used my roadrunner since upgrading yet but I will give it a go later today & see if there is an issue. One question though is have you used the update feature in Efilive to get the very latest update patch? The reason I ask is there was an issue with V7.5 recognising both V1 & V2 at the same time for the license upgrade process. I wonder if this is a related issue.
The Tremor at AIR